HT48RA0 Search Results

Contextual Info: HT48RA0 8-bit Microcontroller Features • • • • • • • • • • Operating voltage: 2.6V~5.2V Ten bidirectional I/O lines Six schmitt trigger input lines One carrier output 1/2 or 1/3 duty On-chip crystal and RC oscillator Watchdog timer 1Kx14 program EPROM

VDD610

Abstract: HT48RA0A
Contextual Info: Vdd 6,10 9 HT48RA0A OSC1 8 1 OSC2 7 FCR4.0MC5 V1H/V1L 3 V2H/V2L CL1 CL2 2 *BUILT-IN LOADING CAPACITOR CL1/CL2=30/30pF +/-20% Oscillating circuit for evaluation

HA0016E

Abstract: HT1621 HT24 HT48CA0 HT6221 HA0018E IC HT48RA0-1
Contextual Info: HT48RA0-1/HT48CA0-1 Remote Type 8-Bit MCU Technical Document • Tools Information · FAQs · Application Note - HA0016E Writing and Reading to the HT24 EEPROM with the HT48 MCU Series - HA0018E Controlling the HT1621 LCD Controller with the HT48 MCU Series

HT48CA0-2

Abstract: HT48RA0-2 HT48RA0A
Contextual Info: HT48RA0-2/HT48CA0-2 Remote Type 8-Bit MCU Features • Operating voltage: 2.0V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · 4 Schmitt trigger input lines · All instructions in 1 or 2 machine cycles

Contextual Info: Remote Type 8-bit MCU HT48RA0-6 Revision: V1.10 Date: ����������������� November 02, 2012 HT48RA0-6 Remote Type 8-bit MCU Table of Contents Features. 4

Contextual Info: HT48RA0-2/HT48CA0-2 Remote Type 8-Bit MCU Technical Document • Tools Information · FAQs · Application Note - HA0016E Writing and Reading to the HT24 EEPROM with the HT48 MCU Series - HA0018E Controlling the HT1621 LCD Controller with the HT48 MCU Series

Contextual Info: HT48RA0-1/HT48CA0-1 Remote Type 8-Bit MCU Technical Document • Tools Information · FAQs · Application Note - HA0016E Writing and Reading to the HT24 EEPROM with the HT48 MCU Series - HA0018E Controlling the HT1621 LCD Controller with the HT48 MCU Series

Contextual Info: HT48RA0-1/HT48CA0-1 Remote Type 8-Bit MCU Technical Document • Tools Information · FAQs · Application Note - HA0016E Writing and Reading to the HT24 EEPROM with the HT48 MCU Series - HA0018E Controlling the HT1621 LCD Controller with the HT48 MCU Series

Contextual Info: HT48RA0-2, HT48RA0-1 HT48RA1, HT48RA3, HT48RA5 Remote Type MCU Handbook March 2005 Copyright Ó 2005 by HOLTEK SEMICONDUCTOR INC. All rights reserved. Printed in Taiwan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without the prior written permission of HOLTEK SEMICONDUCTOR INC.

Contextual Info: HT48RA0-5 Remote Type 8-Bit OTP MCU Features • Operating voltage: · Build-in IR Driver 350mA@3.0V fSYS=4MHz at VDD=2.0V~3.6V (LVR enabled) fSYS=4MHz at VDD=1.8V~3.6V (LVR disabled) · Watchdog Timer · Low voltage reset function · Oscillator types: · Power-down and wake-up features reduce power

alu 9308 d

Abstract: HT48CA0 HT48RA0A
Contextual Info: HT48RA0A 8-Bit Remote Type MCU Features • Operating voltage: 2.2V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · Six Schmitt trigger input lines · All instructions in 1 or 2 machine cycles

holtek ht6221 datasheet

Abstract: HT1621 HT24 HT48CA0 HT6221 HA0016E HA0018E holtek PRODUCT LABEL adcm 2650
Contextual Info: HT48RA0-3/HT48CA0-3 Remote Type 8-Bit MCU Technical Document • Tools Information · FAQs · Application Note - HA0016E Writing and Reading to the HT24 EEPROM with the HT48 MCU Series - HA0018E Controlling the HT1621 LCD Controller with the HT48 MCU Series

HT6221

Abstract: HT48CA0
Contextual Info: Using the HT48CA0 to Generate the HT6221 Output Signals Using the HT48CA0 to Generate the HT6221 Output Signals ：HA0041E D/N Introduction The HT48RA0A/HT48CA0 is a remote microcontroller that can compile remote control codes using the PC.0 port pin as the carrier wave output. The following example explains

electronic ballast for uv tube light

Abstract: DC PL Ballast ignition driver pl lamp ballast 12v lamp driver a boost dc to ac inverter dc-ac inverter ELECTRONIC BALLAST MICROCONTROLLER HT48RA0A uv tube lamp circuits
Contextual Info: HT48RA0A/HT48RA0-1/HT48RA0-2 PL Lamp Driver HT48RA0A/HT48RA0-1/HT48RA0-2 PL Lamp Driver D/N: HA0091E Introduction The PL lamps is driven by inverters, which generally provides a wide range of DC input voltage and transfer it up to be a high frequency and high-voltage output to run the lamps.

Contextual Info: HT48RA0-2/HT48CA0-2 Remote Type 8-Bit MCU Features • Operating voltage: 2.0V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · 4 Schmitt trigger input lines · All instructions in 1 or 2 machine cycles

HT48CA0-1

Abstract: HT48CA0-2 HT48RA0-1 HT48RA0-2
Contextual Info: HT48xA0-1HT48xA0-2 Power-on Reset 時序 HT48xA0-1、HT48xA0-2 Power-on Reset 時序 文件編碼：HA0082T 概述 Remote Type MCU HT48RA0-1/HT48CA0-1、HT48RA0-2/HT48RA0-2 Power-on Reset 的時序圖 如圖-1 所示。總共分為三個部分，由 Setting Time、Warm up time 及 System start up time 所組

HT48RA0-5

Abstract: 0f3htsr1 HT48RA0-3 carl
Contextual Info: 如何使用 HT48RA0-5 的遙控器載波產生功能 如何使用 HT48RA0-5 的遙控器載波產生功能 文件編碼：HA0225T 簡介 HT48RA0-5 是 Holtek 新開發的紅外遙控器 MCU，內建高精度的 4095kHz IRC 頻率，高 Sink 電流的 Carrier 輸出腳 REMDRV 可直接吸納紅外發射二極管的電流而省掉三極管電流放大電

HT48RA0

Contextual Info: HT48RA0 8-bit Microcontroller Features • • • • • • • • • • Operating voltage: 2.6V~5.2V Ten bidirectional I/O lines Six schmitt trigger input lines One carrier output 1/2 or 1/3 duty On-chip crystal and RC oscillator Watchdog timer 1Kx14 program EPROM

3.58MHZ ceramic crystal

Abstract: HT48CA0 HT48RA0A
Contextual Info: HT48RA0A 8-Bit Remote Type MCU Features • Operating voltage: 2.2V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · Six Schmitt trigger input lines · All instructions in 1 or 2 machine cycles

Contextual Info: HT48RA0-5 Remote Type 8-Bit OTP MCU Features • Operating voltage: · Build-in IR Driver 350mA@3.0V fSYS=4MHz at VDD=2.0V~3.6V (LVR enabled) fSYS=4MHz at VDD=1.8V~3.6V (LVR disabled) · Watchdog Timer · Low voltage reset function · Oscillator types: · Power-down and wake-up features reduce power

Laipac

Abstract: HT48RA0A 4mhz resonator
Contextual Info: HT48RA0A 8-Bit OTP IR Remote Controller Features • · · · · · · · · · Operating voltage: 2.2V~3.6V Ten bidirectional I/O lines Six schmitt trigger input lines One carrier output 1/2 or 1/3 duty On-chip crystal and RC oscillator Watchdog Timer 1K´14 program EPROM

Contextual Info: HT48RA0-5 Remote Type 8-Bit OTP MCU Features • Operating voltage: · Build-in IR Driver 350mA@3.0V fSYS=4MHz at VDD=2.0V~3.6V (LVR enabled) fSYS=4MHz at VDD=1.8V~3.6V (LVR disabled) · Watchdog Timer · Low voltage reset function · Oscillator types: · Power-down and wake-up features reduce power

prescaller

Abstract: HT48RA0A HT48RA
Contextual Info: HT48RA0A 8-Bit Remote Type OTP MCU Features • Operating voltage: 2.2V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · Six Schmitt trigger input lines · All instructions in 1 or 2 machine cycles

Contextual Info: HT48RA0A 8-Bit Remote Type OTP MCU Features • Operating voltage: 2.2V~3.6V · 62 powerful instructions · Ten bidirectional I/O lines · Up to 1ms instruction cycle with 4MHz system clock · Six Schmitt trigger input lines · All instructions in 1 or 2 machine cycles