VISHAY CAPACITOR 0805 16V Search Results

Contextual Info: PROJECT NAME: STEVAL-ISV015V1 December 1, 2011 BILL OF MATERIALS Item Quantity Reference Part / Value Voltage Current WATT PACKAGE 1 1 J1 2 1 Cin1 2 pins screw connector 47µF 3 1 C2 1nF 50V 0805 4 1 C4 10nF 50V 0805 5 1 Cout1 10uF 16V 0805 6 1 VR3 0-1k

IHLP2020CZER

Abstract: 1210 capacitor CRCW08050000ZOEA samtec tmm IHLP-2020CZ-01 IHLP-2020CZ-ER DFN12DD DC1667A
Contextual Info: DEMO MANUAL DC1667A LTC3600 16V, 1.5A Synchronous Step-Down Regulator with Programmable Reference Description Demonstration circuit DC1667A is a step-down DC/DC converter using LTC 3600 monolithic synchronous buck regulator. DC1667A has an input voltage range of 4.5V to

RLF7045T

Abstract: led tail light pwm dimming RLF7045 capacitor 100nf 25v 0805 datasheet LM5010 lm321 vishay resistor C4532X7R2A105M AQY221N2S LMV321
Contextual Info: 1-12-05 Rev. 1 LM5010 Brake-Tail LED Drive U1 SW LED1 VIN Vcc CB D1 BST LM5010 CO Tail D3 L1 To Cff RESR ISEN + C IN VCC RON CF1 D2 D4 RON/SD Brake CSS SGND SS RTN FB Vout CFF RFF Vcc U2 RSET RI + - CF2 LM321 RTAIL RBRAKE Q1 PhotoMOS RPHD Theory of Operation

Contextual Info: ADP1877 Reference Design Reference Design PRD 01135 FEATURES Four Output Voltages: 1.2V, 1.8V, 3.3V, 5V Output Current: 1A to 2.2A Input Voltage: 10.8-13.2V DESCRIPTION This ADP1877 Reference Design uses 10.8 V to 13.2 V for the input voltage. The output voltages and currents are

LM5007-8

Abstract: 1uF 250V 0805 10uf/10v C2012X7R2E103K Vishay capacitor TDK 0805 DATASHEET vishay resistor 10nF 250v led tail light pwm dimming PWM theory
Contextual Info: 2-15-05 Rev. 3 LM5007 Automotive LED Drive U1 L1 Vout Vin = 9-40V VIN SW LED1 RCL + + CF1 LM5007 350mA D1 CIN VCC BST RSW RESR CO Vcc CB D2 RON RON RFQ RSET RTN FB Vcc CF2 LM321 + - RI RFF C FF Vout U2 RF Theory of Operation This circuit is designed to replace a single-filament incandescent bulb in an automobile tail light,

murata NPO capacitor

Abstract: murata x7r capacitor 0603 LQN21A LQG21N1R0K10 grm39x7r102k50 murata CAPACITOR 4.7uf LQN21A68NJ04 0805 10V CAPACITOR X7R 4.7UF MIC5205-5.0BM5 GRM39X7R104K16
Contextual Info: RX3 Receiver Board MICRF011 Reference Design With SAW Filter and Pre-Amplifier By Carlos Ribeiro Performance Summary The RX3 receiver board enables the MICRF011 to achieve 300 meters open-field range when used with a 0dBm transmitter. Synopsis The RX3 receiver reference design is intended for high performance applications where low power

Contextual Info: Preliminary Technical Data ADP1877 Reference Design FCDC 00186 FEATURES Four Output Voltages: 1.2 V, 1.8 V, 3.3 V, 5 V Output Current: 1 A to 3.5 A Input voltage: 10.8-13.2 V Ripple 50 mV ppk Transient step ±5%, 50% max load ADP1877 REFERENCE DESIGN DESCRIPTION

planar transformer theory

Abstract: SPM12535T-R60M220 P820 AN1331 LM5033 1331 SMD P8208 zener 13v smd AN-1331 C4532X7R1H685M
Contextual Info: National Semiconductor Application Note 1331 Dennis Morgan May 2004 Introduction • Size: 2.3 x 1.45 x 0.43 in. 1⁄4 brick footprint The printed circuit board consists of 4 layers of 2 oz copper on FR4 material, with a thickness of 0.050 in. It is designed

INDUCTOR 330UH

Abstract: Resistor 100K c38 transistor 0603 33pF 50V X7R resistor 330 ohms 100ME12AX 100uF 250v capacitor vishay c40 capacitor 47UF uCapacitor X7R 1206u transistor c36
Contextual Info: DEMO CIRCUIT 950A LT3825START AND LT3837 QUICK GUIDE LT3825 and LT3837 Non-opto Synchronous Flyback Controller DESCRIPTION Demonstration circuit 950A is a 30W multi-output synchronous flyback converter in 1/8 brick format featuring the LT3825 and LT3837. Output voltage sensing is implemented without the use of opto-coupler, by sensing

SMD resistor 474

Abstract: vishay 0805 SMD resistors diode S1G an4151 smd diode S1G AN-4151 resistor SMD footprint resistor smd capacitor 100nf 50v 0805 datasheet vishay diode s1g sma
Contextual Info: Maxim > App Notes > AUTOMOTIVE DISPLAY DRIVERS POWER-SUPPLY CIRCUITS Keywords: LED, High Brightness, Boost, Step Up, Automotive Nov 19, 2007 APPLICATION NOTE 4151 Using the MAX15005 Supply and Driver for an LED Application Abstract: This reference design is a complete application design for an automotive LED application. It utilizes

AN1370

Abstract: AN-1370 LM5034 LM5034EVAL si7866dp SOT-23 P-MOSFET optocoupler 8 pin configuration
Contextual Info: National Semiconductor Application Note 1370 Dennis Morgan February 2005 Introduction slope compensation, direct interface with opto-coupler transistor, and thermal shutdown. The LM5034EVAL evaluation board provides the power supply design engineer with a fully functional 200W dual interleaved DC-DC power switching regulator using forward/

max11835

Abstract: SMD resistors 0402 817-T010-1401-T670 vishay 0805 SMD resistors SMD RESISTORS piezo transformer driver haptic MAX11851 piezo murata CFT-44TW100-0.6A1-70C
Contextual Info: 19-5507; Rev 0; 9/10 MAX11835 Evaluation System Features The MAX11835 evaluation system EV system demonstrates a complete solution to drive single and multilayer piezo actuators to create haptic feedback for products featuring touch interfaces. The MAX11835

pcb board 0970

Abstract: CRCW08051R00F CRCW08053010F MIC37302 MIC37302BR 0805 Resistor CRCW0805103F
Contextual Info: MIC37302 Evaluation Board Micrel MIC37302 LDO Point-of-Load Evaluation Board Advance Information General Description Features The MIC37302 LDO module is capable of producing regulated output voltage down to 1.25V from an input supply of 5.5V maximum. Main applications include 3.3V to 2.5V and 2.5V to 1.8V at up

Diode 1588

Abstract: LM5001 CMMR1U-2 C4532X C2012X7R2A104K 20MHZ AN-1095 C2012X7R1A105K C2012X7R2A103K C4532X7R3D222K
Contextual Info: National Semiconductor Application Note 1588 Steven Schulte February 2007 Introduction Refer to the LM5001 datasheet for complete circuit design information. The performance of the evaluation board is as follows: Input Range: 16 to 42V Output Voltage: 5V, ±2%

LM27222

Abstract: LM27212 LM27212MTD LM27212MTDX LM27212SQ LM27212SQX MTD48 63M4 0828V
Contextual Info: LM27212 Two-Phase Current-Mode Hysteretic Buck Controller General Description The LM27212 is a two-phase synchronous buck regulator controller that is designed to support high-current loads such as microprocessors. The IC employs a two-phase current-mode hysteretic control

6TPE470MI

Abstract: ap 4749 AN-1220 LM2645 diode-dual VJ0805Y102KXX VJ0805Y103KXX
Contextual Info: National Semiconductor Application Note 1220 Allan Fisher June 2004 Introduction Although a 1µF capacitor is sufficient to ensure stable operation of the internal regulator OUT3, a 10µF ceramic capacitor is installed on board to eliminate the output voltage

opto fet

Abstract: AN3912 capacitor 100nf 50v 0805 vishay C1608COG1H151J zero voltage switching pwm full bridge converter VJ0805Y474KXA capacitor 68nf TLV431ACDBV C2012X7R1A105K C4532X7R1C226M
Contextual Info: Maxim > App Notes > Circuit Protection Hot-Swap and Power Switching Circuits Keywords: MAX5953A, non-isolated, power IC solution, Powered Device, PD, Power-over-Ethernet PoE , detection and classification signatures, IEEE 802.3af, Buck converter Sep 22, 2006

VARIABLE RESISTOR FOOTPRINTS

Abstract: C5750X7R2A475M Si4850DY LM5022 C3216X7R1E105K C4532X7R1H475M CMSH2-60M Si4850EY SLF12575T-330M3R2 c5750x
Contextual Info: National Semiconductor Application Note 1557 Chris Richardson May 22, 2008 Specifications Of The Board Enabling The Converter The Evaluation Board has been designed for testing of various circuits using the LM5022 boost regulator controller. A complete schematic for all the components is shown in Figure

smd transistor t1A

Abstract: lm5033
Contextual Info: User's Guide SNVA091A – May 2004 – Revised May 2013 AN-1331 LM5033 Evaluation Board 1 Introduction The LM5033EVAL evaluation board provides the design engineer with a fully functional intermediate bus converter IBC employing a half-bridge topology. Configured as an IBC, the circuit operates open loop,

VJ0805Y105KXJ

Abstract: LM27222
Contextual Info: LM27212 LM27212 Two-Phase Current-Mode Hysteretic Buck Controller Literature Number: SNVS373A LM27212 Two-Phase Current-Mode Hysteretic Buck Controller General Description The LM27212 is a two-phase synchronous buck regulator controller that is designed to support high-current loads such

Contextual Info: User's Guide SNVA221B – February 2007 – Revised April 2013 AN-1588 LM5001 Evaluation Board 1 Introduction The LM5001 evaluation board is designed to provide the design engineer with a fully functional isolated flyback power converter based on current mode control to evaluate the LM5001 switching regulator IC.

thermistor type R53

Contextual Info: User's Guide SLVU912 – June 2013 TPS65310AEVM and TPS65311EVM Evaluation Module TI's TPS65310AEVM and TPS65311EVM evaluation modules EVM help engineers evaluate the operation and performance of the TPS65310A and TPS65311 power supply IC for safety applications. The

Contextual Info: User's Guide SNVA108A – February 2005 – Revised May 2013 AN-1370 LM5034 Evaluation Board 1 Introduction The LM5034EVAL evaluation board provides the power supply design engineer with a fully functional 200W dual interleaved DC-DC power switching regulator using forward/active clamp topology. A single

HSC201

Abstract: tx102 TX102-6B MICRF009YM QR009HE1 433 transmitter HCS201 pcb layout 2n2907 sot23 rf traNsmitter receiver 315mhz helical 23cm am transmitter HCS201 transmitter
Contextual Info: QwikDemo Kit V Micrel QwikRadio Transmitter/Receiver Microchip Encoder/Decoder Stella Gu & Carlos Ribeiro Introduction 3 QR009HE1 The QwikDemo Kit V is a tool to provide demonstration of the QwikRadio® products. The special example is given through the Year of 2005 Product winner MICRF009 and